Was that during COVID? I regularly eat Chipotle around the US and I’ve never encountered this requirement, I always order at the counter so it is fresh.

The quotes in your comment will make people think you’re telling the truth.

“Again, we believe Bret Baier and Martha MacCallum, the faces of our political coverage, are the best choices to moderate.”

You’re already on hundreds of cameras by walking into any airport in the world. Do they need your consent to run facial recognition software on the security footage?

Did you read the article? The full title of the livestream was, “Will the Deep State Assassinate Biden If He Refuses To Leave?”

As far as I can tell, the title was clickbait and he did not encourage violence, but I would love to be corrected. Look, I hate defending this guy, I’m just doing this because I hate sensational headlines.

Seriously? Asking for a source makes me a troll? I’m a skeptic of all things and I’m tired of everyone on all sides exaggerating and editorializing news. It seems like most people in the comments didn’t read the article, or maybe they’ve seen some other articles that they aren’t linking to. I don’t listen to Alex Jones so I don’t know what he’s saying on this topic but it’s not covered in this article.

I hate Alex Jones but I don’t follow your logic. Can you be less ambiguous to help me out? What did Alex say? I can’t find a single article supporting what these commenters claim, not even this post’s article. It seems like everyone is making stuff up after reading the headline and not even clicking the link to read it.

I ask because the article says nothing about him encouraging others to do it. I was hoping someone would link or explain more.

Did he? The full title of the stream was, “Will the Deep State Assassinate Biden If He Refuses To Leave?” Seems like it was just clickbait because the article says nothing about Alex encouraging it.

The full title of the livestream was, “Will the Deep State Assassinate Biden If He Refuses To Leave?”

Yes the hotend heats up and has molten plastic inside it and it gets pushed out the nozzle. I’m honestly not sure why they offer all those different versions as accessories. It includes a hotend and 0.4mm nozzle.

If you have a catastrophic issue it’s possible for the hotend to be clogged completely, but that’s never happened to me. It comes with a declogging tool which is just a long pokey wire to push up through the nozzle while it’s hot to clear it.

The nozzle itself can unscrew from the hot end and be replaced because it wears out over time from filament chipping away at it.

Also, you might want different nozzle diameters depending on what you’re printing. You can just buy spare nozzles without an entire hotend.

It comes with 0.4mm and they offer a range from like 0.2-1.0mm. The smaller nozzles print slower and more detailed while the larger nozzles are faster with lower resolution.

There’s a rabbit hole of things that can go wrong and things that need to be calibrated and upgraded. I had to assemble the Ender 3 and ensure that everything was perfectly straight, level, and 90 degrees. Calibrate the z-offset so it knows where the nozzle is.

I added an auto bed leveling sensor to my Ender 3, and that required custom firmware, and I replaced the bed springs because it wasn’t staying level.

I calibrated the e-steps because it wasn’t extruding consistently, then ended up replacing the extruder because it was cheap and unreliable.

Humidity was ruining my filament on the spools and making it brittle and snapping so I built a dry box that could feed the printer, similar to the clear boxes on some Bambu models.

The Bambu really was as simple as unboxing and turning it on. It comes pre-assembled and includes a lot more sensors that are able to keep it working smoothly.

My vote is for Bambu printers. I started with a super cheap Ender 3 V2 in 2020 and recently we got a Bambu X1 at work and it’s so much easier, faster, and better. No more hours of troubleshooting issues, it just calibrates itself and goes.

The P1P is cheaper and might be a good option to look at. These printers are highly recommended on the reddit community too.

https://store.bambulab.com/collections/3d-printer

Yeah and it seems obvious that they shouldn’t be driving vehicles where people are laying. This is the third person I’ve heard of being run over by police on a beach this summer.

Thanks, I think the RGB shirt might be custom to him because the same image is his YouTube channel’s profile header image.

Does Technology Connections sell shirts? In most of his recent videos he has worn a black shirt with zoomed in RGB pixels from a digital display and I’ve been looking for it everywhere because I work in a related industry.

Side question: Should’t it also be illegal for Hallie Biden to dispose of an illegal firearm by putting it in a trash can outside a grocery store for a random person to find? That seems like a very irresponsible way to handle a firearm and evidence.

Cultural smells are interesting. In Japan, they find the strong scents of perfume, cologne, and even shampoo that westerners wear to be intolerable and people at restaurants will discreetly ask to change tables to move away from those wearing it. They are more sensitive to fragrances there while Americans have fragrance in almost everything.

Of course, the most respectful thing to do when traveling is to just take a shower and wear a neutral deodorant so that you’re not giving off any unique smells.

This situation sure sounds like it blew up into a racist power trip though.

Thanks I’m going to give this a try.

You can opt into it and other beta technologies at Google Labs.

Congrats! It’s scary, but this is when you finally have the freedom to live your unique life. Stay in touch with your close friends, everyone else will fade away. And remember, wear sunscreen.